Power Supplies for Your Homelab: 80+ Efficiency, Redundant PSUs, and Server PSU Quirks

Every build guide tells you to “get a good power supply” and leaves it there, as if that settles the question. It doesn’t. A PSU is the one component that touches every watt your homelab ever draws, and the difference between a cheap unit and a good one shows up as heat, noise, and a power bill you can actually measure, not just a line on a spec sheet. This is the PSU side of the picture: what the efficiency ratings mean, how server PSUs differ from the ATX unit in a tower build, and what redundant power supplies actually buy you once you start running used enterprise gear. ...

October 10, 2026 · 7 min

Multi-Bay DAS Enclosures: Expanding Drive Bays Without Building a Second NAS

Every data hoard eventually outgrows its case. The main server is full, the HBA’s ports are full, and the next logical move looks like building a second NAS from scratch, a second motherboard, a second CPU, a second OS to patch and monitor. Before doing that, it’s worth asking whether the actual problem is “I need more compute” or just “I need more drive bays,” because those are different problems with different, much cheaper answers. A DAS enclosure is the second answer: a box of drive bays with no brain of its own, attached to a host system that already exists. ...

October 6, 2026 · 6 min

Taming Noise and Heat: Running Enterprise Gear Quietly in a Home Environment

Anyone who’s bought a used enterprise server for a homelab has had the same moment: it powers on, the fans spin up to full speed for the POST sequence, and for about fifteen seconds it sounds like the room is about to take off. Most of the time it settles down after boot. Sometimes it doesn’t, and that’s when the real work starts. Noise and heat are two sides of the same problem in a home environment, and neither one is solved by just wanting it to be quieter. ...

October 2, 2026 · 7 min

Building a Homelab Rack: Choosing a Cabinet, Rails, PDU, and Cable Management

Every hardware guide on this site so far has assumed the rack already exists. Buying used enterprise gear, sizing a UPS, picking a managed switch, all of it takes for granted that there’s somewhere to physically put the thing. That assumption falls apart fast for anyone starting from a mini PC on a shelf and a switch zip-tied to the underside of a desk. This is the article that comes before all of those: the cabinet itself, the rails that hold gear in it, the power distribution feeding it, and the cable management that decides whether adding a fourth device is a five-minute job or an afternoon of re-routing everything you already installed. ...

September 28, 2026 · 8 min

Choosing SSDs for Your Homelab: Consumer vs Enterprise, and Where Endurance Actually Matters

Every homelab ends up with SSDs doing several different jobs at once: booting the hypervisor, holding VM disks, backing a ZFS special vdev or SLOG, maybe just serving as bulk fast storage for a database. Most buying advice treats this as one decision, “get an SSD, more capacity is better,” and stops there. That’s fine for a boot drive. It’s a real mistake for anything doing sustained writes, and it can quietly cost you data integrity on a ZFS log device. The differences between consumer and enterprise flash are specific and they map directly onto which job a drive should actually do. ...

September 24, 2026 · 7 min

Picking a CPU and Motherboard for Your Proxmox Homelab: What Actually Matters

Most homelab buying guides start with the case or the drives, but the CPU and motherboard decide almost everything downstream of them. PCIe lane count sets how many cards you can run at once. ECC support decides whether a bit flip in RAM silently corrupts your ZFS pool or gets caught and corrected. IOMMU group layout decides whether GPU or HBA passthrough to a VM is a ten-minute config change or a wall you can’t get past no matter what you try. None of that shows up on a spec sheet the way clock speed and core count do, which is exactly why it gets skipped over until someone hits it the hard way. ...

September 20, 2026 · 6 min

Choosing a Managed Switch for Your Homelab: What Actually Matters

Every homelab guide eventually tells you to “get a managed switch,” usually without saying why, or which one, or what happens if you buy the wrong one. This site has already covered when 10GbE is worth the upgrade and how to configure VLANs, bridges, and bonding once you’re inside Proxmox. This article is the piece that comes before both of those: picking the actual switch hardware sitting between your gear, the decision that either makes everything downstream easy or makes you fight your network for the next three years. ...

September 16, 2026 · 7 min

Sizing a UPS for Your Homelab (and Setting Up NUT for Automatic Shutdown)

A UPS without a way to talk to your hosts is just an expensive surge protector with a battery in it. It’ll keep the lights on for a few minutes, but the moment that battery runs out, every VM and container you’re running goes down exactly as hard as it would have without a UPS at all, just a little later. The part that actually protects you, a UPS that tells your hosts “power’s out, shut down now while you still can,” is a separate piece of software most people never get around to setting up. Here’s how to size the UPS itself, and how to wire up Network UPS Tools (NUT) so an outage ends in a clean shutdown instead of a dirty one. ...

September 12, 2026 · 9 min

IPMI, iDRAC, and iLO: Setting Up Out-of-Band Management for a Headless Homelab

Most homelab hardware guides stop at “buy it, rack it, install Proxmox.” The thing that actually changes how a homelab feels to run day to day is whether you can reach the machine when the OS won’t boot, the network stack is misconfigured, or the box is three rooms away in a closet with no monitor attached. That’s what out-of-band management is for, and if you’re running used enterprise gear, you almost certainly already own it. Most people never turn it on. ...

September 8, 2026 · 8 min

HBA Cards and IT Mode Flashing: The Real Way to Connect a Homelab's Worth of Drives

Every data hoarder eventually hits the same wall: the motherboard only has six SATA ports, and the build calls for twelve drives. The instinctive fix is a cheap RAID card off eBay, and that instinct is almost always wrong. The actual answer, in nearly every homelab storage build, is an HBA flashed to IT mode. Here’s what that means, why it matters, and how to do it without turning a $40 card into a paperweight. ...

September 4, 2026 · 7 min