A Raspberry Pi (or one of the many ARM and low-power x86 boards that compete with it) ends up in most homelabs eventually, usually running Pi-hole, a single sensor-reading job, or sitting in a drawer after an abandoned project. Few people run their whole stack on one, and that’s correct, but “not your main box” and “not worth having” are very different conclusions. The useful question is which specific jobs a single-board computer (SBC) is actually the right tool for, and which jobs people keep trying to force onto one when a mini PC would save them the trouble.
What an SBC actually is, for this purpose
A single-board computer is a complete computer, CPU, RAM, storage interface, and I/O, built onto one small board with no separate case or power supply required. The Raspberry Pi is the best-known example, but the category includes boards from Radxa, Orange Pi, Banana Pi, and others, most running ARM CPUs, some running low-power x86. For a homelab, the practical differences that matter are: how much RAM it supports (most top out at 8GB, a few newer boards reach 16GB), whether it boots from an SD card or has a real NVMe/eMMC option, how much power it actually draws, and how good its OS and container ecosystem support is.
The Raspberry Pi 4 and 5 are the default recommendation specifically because of software support, not raw specs. Debian-based Raspberry Pi OS, mainline kernel support, and the sheer volume of people running Docker and k3s on them means you’ll find a documented answer to almost any problem. Cheaper ARM boards from other vendors are often better value on paper (more RAM or a faster CPU for less money) and worse in practice, because you’re the one debugging a half-supported vendor kernel fork when something doesn’t work.
Where an SBC is the right answer
Single always-on, low-load services. Pi-hole or AdGuard Home, a single Home Assistant instance for a small smart-home setup, an MQTT broker, a single Uptime Kuma check-in point, a Tailscale/WireGuard exit node. These want to be on 24/7, draw almost nothing, and don’t need to share hardware with anything heavier. A Raspberry Pi drawing 3-7W idle costs pennies a month to run and doesn’t need to compete for resources on your Proxmox box.
A dedicated, physically separate monitoring point. If you want something watching your main homelab’s uptime that isn’t itself running on the hardware it’s watching, a cheap SBC on its own power source (ideally its own small UPS or at least a separate circuit) is the honest way to do it. If the box being monitored and the box doing the monitoring share the same host, a host-level failure takes down your visibility into the failure at the same time.
k3s worker nodes in a small cluster, as a learning or genuinely distributed project. Several Raspberry Pis (or a mix of Pis and mini PCs) running k3s is a legitimate way to learn real Kubernetes mechanics, cordoning nodes, pod scheduling across heterogeneous hardware, and dealing with ARM-only or multi-arch container images. It’s also genuinely useful for workloads you want physically redundant across more than one small box rather than one bigger one. This is covered in more depth in the k3s/k0s/MicroK8s comparison elsewhere on this site, but the hardware point stands on its own: a cluster of cheap SBCs is a real, not purely academic, pattern.
Physical-presence or GPIO-adjacent jobs. Anything that needs to read a sensor, control a relay, talk to a camera over a ribbon cable, or sit physically near a piece of equipment it’s monitoring. This is the one category a mini PC genuinely can’t compete in, GPIO pins and a well-documented hardware ecosystem are the Pi’s actual unique advantage over everything else on this list.
PoE-powered deployments. With a PoE HAT (or a board with PoE built in), an SBC can run off a single Ethernet cable with no separate power brick at all, which matters if you’re placing it somewhere a power outlet is inconvenient. The PoE-for-homelab article on this site covers the switch and injector side of that in more detail.
Where people keep forcing it and shouldn’t
Running Proxmox itself. Proxmox wants x86_64, and while there are community ARM virtualization projects, you’re giving up the entire point of using Proxmox (a mature, widely documented hypervisor) to run an unofficial port on hardware it wasn’t built for. If you want a tiny always-on hypervisor box, that’s what the mini-PC-vs-custom-build comparison on this site is for, not an SBC.
Anything that needs real sustained I/O. A Raspberry Pi’s storage interface, whether SD card, USB 3, or the newer PCIe/NVMe options on the Pi 5, is nowhere near what even a budget mini PC’s NVMe slot delivers. Running a database with real write volume, a media library’s Plex/Jellyfin metadata scanning, or anything doing sustained file I/O against spinning disks is going to bottleneck on the SBC’s I/O path long before it bottlenecks on CPU.
Hardware transcoding. The Raspberry Pi’s GPU can decode some formats but it is not a transcoding engine in the sense Plex or Jellyfin need for serving multiple simultaneous streams at varying quality. A mini PC with a modern Intel iGPU and Quick Sync, covered in the GPU-selection article on this site, does this job properly for a fraction of the hassle.
Anything where you’ll fight ARM compatibility more than you’ll save money. A huge amount of the self-hosted container ecosystem publishes multi-arch images now, but not all of it does, and the ones that don’t tend to be exactly the less-common, more-interesting apps you actually wanted to try. If you find yourself building your own container image from source because the upstream project only ships amd64, stop and ask whether a $100-150 mini PC would have saved you three hours of yak-shaving. Often it would have.
The SD card trap, and how to actually avoid it
This is the single most common SBC failure mode, and it’s avoidable. SD cards are not designed for the write patterns of a general-purpose Linux root filesystem, logs, journald, swap activity, and database writes all generate the kind of small, repeated writes that wear out flash storage faster than sequential writes do. A Pi running Pi-hole or Home Assistant off a cheap SD card will often run fine for a year or two and then fail with filesystem corruption, usually discovered the hard way when it won’t boot.
The fixes, in order of how much they actually help:
- Boot from USB SSD or NVMe instead of SD, if the board supports it. The Raspberry Pi 4 and 5 both support USB boot, and the Pi 5 has a proper PCIe lane for an NVMe hat. This is the real fix, not a mitigation, a decent USB SSD is both faster and dramatically more write-durable than any SD card.
- If you’re stuck on SD card, move logs and anything write-heavy to tmpfs (RAM) or an external drive.
log2ramis the common tool for this on Raspberry Pi OS, it redirects/var/logto a RAM-backed filesystem and flushes to disk on a schedule instead of on every write. - Buy a card actually rated for continuous write workloads (application-class A1/A2, high endurance), not just a fast card. Read/write speed and write endurance are different specs, a card optimized for camera burst shooting is not the same thing as one optimized for years of small continuous writes. SanDisk and other vendors sell dedicated “high endurance” lines specifically for dashcams and surveillance use, and those are a far better fit for a 24/7 Linux root filesystem than a generic fast card.
- Keep a backup image, and make it routine, not a one-time setup step.
rpi-cloneor a periodicdd/rsyncof the SD card or boot drive to a NAS means a dead boot medium costs you a re-flash and a restore, not a lost configuration you have to rebuild from memory.
None of this is exotic. It’s the same lesson as everywhere else in homelabbing: know what your storage medium is actually good at, and don’t run a workload against its weak point.
Bottom line
An SBC earns its place in a homelab as a cheap, low-power, always-on appliance for one focused job, DNS filtering, a single home-automation hub, a monitoring node physically separate from what it’s watching, or a GPIO-connected sensor project. It is not a replacement for a real Proxmox box, and trying to stretch it into one, running a hypervisor, a database with real write volume, or transcoding, just means fighting the hardware instead of using it for what it’s actually good at. If you’re buying one, spend the extra ten or fifteen dollars to boot from USB or NVMe instead of an SD card, you’ll thank yourself in a year when it’s still running instead of silently corrupting itself.